DUMPS BASE EXAM DUMPS DELL EMC DES-4122 28% OFF Automatically For You Specialist - Implementation Engineer PowerEdge Version 2.0 New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass 1.A technician is creating a virtual disk in the iDRAC (2x 4 TB NL-SAS in RAID 1) to install Windows 2016 They manually boot to the OS installation media without using the Lifecycle Controller OS Deployment wizard Only the first 2048 GB on the virtual disk can be partitioned How should the technician obtain access to the remaining 2 TB (approximately) of storage? A. Use the Lifecycle Controller OS Deployment Wizard to deploy the OS on this server B. Delete the 4 TB virtual disk and create a virtual (boot) disk no larger than 2048 GB C. Upgrade to a newer version of the operating system D. Use F2 to go into the BIOS, change the BIOS boot mode to UEFI, and try again Answer: D 2. Where is the data stored to allow Easy Restore to successfully complete a system board replacement? A. NAND Flash module on the disk drive mid plane B. IDSDM SD card C. vFlash SD card D. Serial Flash storage in the server's front panel Answer: D 3. A technician needs to repurpose a Dell EMC PowerEdge server. The server has dual processors with 18 cores each The OS only "sees" 24 threads in total. Which setting should the technician change in Processor Settings in the System BIOS? A. System Profile B. Virtualization Technology C. HyperThreading D. Number of Cores per Processor Answer: D 4. What are the default settings used when applying firmware and a configuration to a replaced part using the Lifecycle Controller? A. Firmware: Upgrade to latest available version Configuration Apply always B. Firmware Allow version upgrade only Configuration: Disabled C. Firmware: Match firmware of replaced part Configuration Apply always D. Firmware Disabled New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass Configuration Apply only if firmware match Answer: C 5. What is the purpose of the Silicon-Based Hardware Root of Trust feature in Dell EMC PowerEdge 14G servers? A. Ensures that the installed operating system is authentic B. Ensures that the server has a valid Service Tag number C. Ensures that no unauthorized BIOS or firmware codes are run D. Ensures that the server boots only when connected to a verified network Answer: C 6. DRAG DROP Match each status LED indicator on the Dell EMC 14G PowerEdge server with its corresponding condition. Answer: New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass 7. An engineer is checking a newly delivered Dell EMC PowerEdge R640 server that will be deployed for a new database environment. The inventory consists of: The server power configuration will be set for gnd redundancy. The management switch is 1000 Base-T and the top of rack switches 10Gb What additional component(s) is needed for this configuration? A. Hot-plug power supply, 750 W - qty 1 B. Hot-plug power supply, 1100W - qty 1 C. Dell Networking, cable, 40GbE (QSFP+) to 4 x 10GbE SFP+ passive copper breakout cable, 3 meters - qty 2 D. C20 to C21, PDU style, 250 V, 16 Amp, 3 5 meters power cord - qty 2 Answer: D 8. What is a systems management console solution optimized for monitoring and managing Dell enterprise and remote office hardware? A. SupportAssist Enterprise B. iSM C. OpenManage Essentials D. iDRAC9 New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass Answer: C 9. DRAG DROP Refer to the exhibit. Match each callout to the Dell EMC PowerEdge server model shown. New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass Answer: 10. After completing a disk rebuild operation, a technician needs to configure the system so that the rebuild process happens faster the expense of slowing users down. Which setting should be changed? A. Rebuild Rate in the BIOS settings B. System Profile to Performance in the BIOS settings C. System Profile to Performance in the iDRAC GUI D. Rebuild Rate in the iDRAC GUI Answer: D New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass 11. An engineer wants to fully leverage Microsoft Windows Server 2016 for TPM- based guarded host deployment of a 14G server. Which BIOS settings need to be used for installing the Windows server? A) B) C) D) A. Option A New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass B. Option B C. Option C D. Option D Answer: D 12. A company that has very specific firmware requirements has acquired Dell EMC PowerEdge servers Any replaced parts of the type must match the original parts identically. The procedure must be as simple as possible with minimal risk. What action should a technician take to help accomplish this goal? A. Configure servers to access the remote firmware repository B. Enable the Match Firmware of Replaced Part setting in the system BIOS C. Install and configure a repository manager D. Enable the Collect System Inventory On Restart (CSIOR) attribute Answer: B 13. DRAG DROP Match each RAID level to its characteristic. Answer: New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass 14. A technician installs eight servers into a fully operational rack with top of rack switch Each server has a quad 1Gb NIC and redundant power supplies. The company uses iDRAC in shared LOM mode with LOM1 as the selected NIC What should the technician do to verify iDRAC connectivity on each server? A. iDRAC Datacenter license is installed. B. Ethernet port LOM1 is cabled and the link light is green. C. iDRAC dedicated NIC port is cabled and the link light is green D. iDRAC Enterprise license is installed Answer: B 15. Dell EMC PowerEdge 14G servers support which technology? A. Quicksync 1.0 B. Intel Boot Guard C. AMD GuardMI D. iDRAC8 Answer: C 16. Which type of access is known as Firmware RACADM on a Dell EMC PowerEdge server? A. Accessing RACADM running the Dell Toolkit B. Accessing RACADM with OpenManage software C. Logging into iDRAC using SSH or Telnet D. Logging into iDRAC through Boot Manager Answer: C 17. A Dell EMC PowerEdge 14G server uses Intel OPTANE DC Persistent Memory in App Direct mode . What is the minimum size DIMM supported for this type of memory? A. 64 GB B. 128 GB C. 256 GB D. 512 GB Answer: B 18. A technician needs to change the iDRAC password on a Dell EMC PowerEdge 14G server in a lights-out datacenter. The be rebooted because it is in production. New DELL EMC DES-4122 Dumps V10.02 with PDF Questions and Answers For Pass The iDRAC is configured with the default credentials How could the technician change the iDRAC password? A. SupportAssist Enterprise B. iDRAC Web GUI C. OpenManage Server Administrator D. Virtual Console; press F2 after rebooting system Answer: D GET FULL VERSION OF DES-4122 DUMPS