Kia Global Information System (KGIS) Page 1 of 2 SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body (Interior and Exterior) Replacement Put on gloves to prevent hand injuries. • When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components. • Be careful not to scratch the door trim and other parts. 1. Using a screwdriver or remover, remove the front door quadrant inner cover (A). 2. Using a flat-tip or remover, remove the front door pull handle mounting cap (A). 3. Loosen the mounting screw and remove the front door trim (A). https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_8_3_2&sitinfolist=91^... 19.01.2020 Kia Global Information System (KGIS) Page 2 of 2 4. Remove the front door inside handle cage (A). 5. Disconnect the front door twitter speaker connector (A), and window switch connector (B), mirror switch connector (C). 6. To install, reverse removal procedure. • Make sure the connector is connected properly. • Make sure the door locks / unlocks and opens / closes properly. • Replace any damaged clips (or pin-type retainers). • Make sure the glass is operated properly. https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_8_3_2&sitinfolist=91^... 19.01.2020 Kia Global Information System (KGIS) Page 1 of 1 SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body (Interior and Exterior) Replacement 1. Remove the front door trim. (Refer to Front Door - "Front Door Trim") 2. After loosening the mounting screws, remove the front door inside handle (A). 3. To install, reverse removal procedure. • Make sure the door locks / unlocks and opens / closes properly. • Replace any damaged clips (or pin-type retainers). https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_8_4_1&sitinfolist=91^... 19.01.2020 Kia Global Information System (KGIS) Page 1 of 1 SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body (Interior and Exterior) Component Location 1. Rear door trim https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_9_3_1&sitinfolist=91^... 19.01.2020 Kia Global Information System (KGIS) Page 1 of 3 SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body (Interior and Exterior) Replacement Put on gloves to prevent hand injuries. • When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components. • Be careful not to scratch the door trim and other parts. 1. Using a screwdriver or remover, remove the rear door delta inner cover (A). 2. Using a flat-tip or remover, remove the rear door pull handle mounting cap (A). 3. Loosen the mounting screw and remove the rear door trim (A). https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_9_3_2&sitinfolist=91^... 19.01.2020 Kia Global Information System (KGIS) Page 2 of 3 4. Remove the rear door inside handle cage (A). 5. Disconnect the power window switch connector (A). https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_9_3_2&sitinfolist=91^... 19.01.2020 Kia Global Information System (KGIS) Page 3 of 3 6. To install, reverse removal procedure. • Make sure the connector is connected properly. • Make sure the door locks / unlocks and opens / closes properly. • Replace any damaged clips (or pin-type retainers). • Make sure the glass moves properly. https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_9_3_2&sitinfolist=91^... 19.01.2020 Kia Global Information System (KGIS) Page 1 of 1 SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body (Interior and Exterior) Replacement 1. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim") 2. After loosening the mounting screws, remove the rear door inside handle (A). 3. To install, reverse removal procedure. • Make sure the door locks / unlocks and opens / closes properly. • Replace any damaged clips (or pin-type retainers). https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_9_4_1&sitinfolist=91^... 19.01.2020 Kia Global Information System (KGIS) Page 1 of 1 SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body (Interior and Exterior) Component Location 1. Luggage side trim https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_18_3_1&sitinfolist=91... 19.01.2020 Kia Global Information System (KGIS) Page 1 of 2 SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body (Interior and Exterior) Replacement Put on gloves to prevent hand injuries. • When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components. • When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface. • Take care not to bend or scratch the trim and panels. 1. Remove the rear seat assembly (Refer to Rear Seat - "Rear Seat Assembly") 2. Carefully remove the rear door body side weatherstrip. 3. Carefully remove the liftgate weatherstrip. 4. Remove the rear door scuff trim. (Refer to Interior Trim - "Door Scuff Trim") 5. Remove the rear transverse trim. (Refer to Liftgate Trim - "Rear Transverse Trim") 6. After loosening the mounting bolt, remove the rear seat belt lower anchor (A). Tightening torque : 39.2 - 53.9 N·m (4.0 - 5.5 Kgf·m, 28.9 - 39.8 lb·ft) 7. After loosening the mounting screws, remove the luggage side trim (A). https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_18_3_2&sitinfolist=91... 19.01.2020 Kia Global Information System (KGIS) Page 2 of 2 8. Press the lock pin and separate connector (A). 9. To install, reverse removal procedure. place any damaged clips (or pin-type retainers). https://www.kiatechinfo.com/viewer/print_pop.aspx?pos=1$7_18_3_2&sitinfolist=91... 19.01.2020 SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body Electrical System Inspection • Do not cause shock to the speakers by dropping or throwing them. • Be careful not to drop water and oil on the speakers. • Use caution to handle the speaker because diaphragm made of paper is easily torn by impact or external force. • Audio system tuning may cause damage to the speakers. The modified speakers are not covered by the manufacturer’s warranty. Basic inspection 1. Loosen the screws to rule out the interference from the body trims and surrounding parts and then remove the speaker. 2. After removing the speaker, check the sound quality of the speaker with the connector plugged in. Inspection for each cause 1. Abnormal vibration (1) Make sure the mounting screws are properly tightened before replacing the speaker. (2) Reinstall the speaker and check that the symptom is resolved. (3) If the symptom does not disappear, replace the speaker with a new one. 2. Noise (1) Check that the speaker connector is properly connected and reinstall the connector if necessary. (2) If noises occur in the radio mode, turn to the media player mode. (3) If noises occur in both modes, replace the speaker with a new one. If noises occur only in the radio mode, the poor radio reception is the cause so do not replace the speaker. 3. Poor working (1) Check the plus (+) and negative (-) speaker terminals using an ohmmeter. If resistance is measured at the specified value shown below, the speaker operation is normal. Front Door speaker :2.0 Ω Rear Door speaker :4.0 Ω Center speaker :2.0 ± 0.3 Ω Tweeter speaker :4.0 ± 0.6 Ω Midrange speaker :2.0 ± 0.3 Ω Sub woofer :2.0 ± 0.3 Ω per coil (4.0 ± 0.6 Ω coil in series) (2) If the measured resistance is different from the specified value, replace the speaker. Removal Front Door Speaker 1. Remove the front door trim. (Refer to Body - "Front Door Trim") 2. Disconnect the connector (A) and then remove front door speaker (B) by loosening the screws. Rear Door Speaker 1. Remove the rear door trim. (Refer to Body - "Rear Door Trim") 2. Disconnect the connector (A) and then remove rear door speaker (B) by loosening the screws. Tweeter Speaker 1. Disconnect the negative (-) battery terminal. 2. Remove the crash pad side cover (A). 3. Remove the side air ventilation duct assembly (A) after loosening the screw. 4. Remove the tweeter speaker (A) by loosening the screws after disconnecting the connector (B). Crash Pad Center Speaker 1. Disconnect the negative (-) battery terminal. 2. Remove the center speaker grille (A). 3. Remove the center speaker (A) after loosening the screws. 4. Disconnect the center speaker connector (A). Midrange Speaker 1. Remove the front door trim. (Refer to Body - "Front Door Trim") 2. After removing the connector (A) from the bracket by pushing it direction of arrow, disconnect the speaker connector. 3. Remove the midrange speaker (A) by loosening the screws. Subwoofer 1. Disconnect the negative (-) battery terminal. 2. Remove the luggage side trim. (Refer to Body - "Luggage Side Trim") 3. Disconnect the connector (A). 4. Remove the subwoofer (A) by loosening the nuts. Installation 1. Install in the reverse order of removal. SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body Electrical System Component Location 1. AMP SOUL(SK3) > 2020 > G 1.6 T-GDI GAMMA > Body Electrical System Connector and Terminal Function Function Pin Connector A Connector B 1 Battery (+) Sub woofer speaker 2 (+) 2 Battery (+) Sub woofer speaker 1 (+) 3 Battery (+) Right front door speaker (+) 4 Battery (+) Left front door speaker (+) 5 - - 6 MM-CAN (High) - 7 MM-CAN (Low) - 8 ACC - 9 Amplifier navigation voice (+) - 10 - - 11 - - 12 Right tweeter speaker (+) Right midrange speaker (+) 13 Left tweeter speaker (+) Left midrange speaker (+) 14 Front center speaker (+) Right rear door speaker (+) 15 - Left rear door speaker (+) 16 Ground Sub woofer speaker 2 (-) 17 Ground Sub woofer speaker 1 (-) 18 Ground Right front door speaker (-) 19 Ground Left front door speaker (-) 20 Amplifier SPDIF (High) - 21 Amplifier SPDIF (Low) - 22 Amplifier SPDIF (Ground) - 23 Amplifier navigation voice (-) - 24 - - 25 Right tweeter speaker (-) Right midrange speaker (-) 26 Left tweeter speaker (-) Left midrange speaker (-) 27 Front center speaker (-) Right rear door speaker (-) 28 - Left rear door speaker (-)
Enter the password to open this PDF file:
-
-
-
-
-
-
-
-
-
-
-
-