The "Ultimate Evil" One Bar Prison Addendum 1 - Hismith Kliclok May 2023 This addendum to the "Ultimate Evil" One Bar Prison Construction and Usage manual V1.1b describes the changes needed to use Hismith Kliclok accessories with the device. Revision/Update Information: V1.0a / This is a new manual. https://www.evilobp.fun https://www.reddit.com/r/OneBarPrison May 6, 2023 This document and included images are licensed under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0) license. Contact the author via one of the methods listed in the main "Ultimate Evil" One Bar Prison Construction and Usage manual if you would like to discuss alternate licensing and usage rights. The information in this document is prepared for entertainment purposes only. It should not be construed as any representation by the author as to the safety or reliability of the described device. The author expressly disclaims any implied warranties of merchantability or fi tness for any particular purpose. DANGER: Improper usage can result in severe injury or death. Never use without another trained person present at all times . Use common sense. TRADEMARKS USED IN THIS MANUAL Any trademarks mentioned in this manual are acknowledged to be the property of the trademark owners and are used solely for identi fi cation purposes. Contents PREFACE iv CHAPTER 1 INTRODUCTION 1–1 CHAPTER 2 NECESSARY AND OPTIONAL PARTS 2–1 CHAPTER 3 ASSEMBLING THE KLICLOK CONNECTOR AND POLE ADAPTER 3–1 3.1 PREPARING THE POLE ADAPTER 3–1 3.2 DISASSEMBLING THE KLICLOK SYSTEM DOUBLER 3–1 3.3 ASSEMBLING THE KLICLOK CONNECTOR TO THE POLE ADAPTER 3–2 CHAPTER 4 MODIFYING THE KLICLOK CONNECTOR TO PREVENT ESCAPE 4–1 FIGURES 1–1 Completed pole adapter with Hismith Kliclok connector and metal dildo 1–1 1–2 Hismith polished metal dildos 1–2 1–3 Hismith silicone dildos (realistic and fantasy) 1–3 3–1 Kliclok System Doubler and Wrench 3–2 3–2 Assembly of parts in pole adapter 3–3 3–3 Completed assembly of Kliclok to pole adapter 3–4 4–1 Kliclok connector showing unmated and mated differences 4–1 4–2 Loose cable tie on the pole adapter 4–2 4–3 Cable tie tightened and cut fl ush 4–3 4–4 Kliclok connector showing cut cable tie 4–4 iii Preface This addendum to the "Ultimate Evil" One Bar Prison Construction and Usage manual V1.1b describes the changes needed to use Hismith Kliclok accessories with the device. A future revision of the "Ultimate Evil" One Bar Prison Construction and Usage manual will incorporate this information. Intended Audience This manual addendum is intended for fellow kinksters. Important Warning DANGER: Do NOT do stuff that can get you or anyone else injured or killed. That is always good advice, regardless of whether you’re driving to work, skydiving, or using a One Bar Prison. Conventions In this document, the following conventions will be used: • Captive - the person who the One Bar Prison is restraining. Some materials refer to this as the "victim" or by other terms. I prefer the term "captive" as "victim" implies at least some unwillingness or lack of consent. • Captor - one or more people responsible for the operation of the One Bar Prison as well as ensuring the safety of the captive at all times • One Bar Prison (OBP) - the actual device, including any accessories. • Device - in this document, refers specifically to the "Ultimate Evil" One Bar Prison. • Note calls your attention to particular points of construction or usage where more than the expected level of attention to instructions is required. • Caution indicates that failing to follow a procedure may cause damage to the OBP or its components. • WARNING indicates that particular care must be taken to prevent possible personal injury. • DANGER indicates that particular care needs to be taken to prevent severe personal injury or death. iv 1 Introduction As described in the main "Ultimate Evil" One Bar Prison Construction and Usage manual, the device uses a standard 3XLR connector to attach the interchangeable dildos to the device. While this is a standard connector type for "fucking machine" type devices, some dildos are not available with a 3XLR attachment. Another standard attachment method is the Hismith Kliclok. This is a proprietary 8-sided latching connector with a quick disconnect. This addendum describes how to attach a Kliclok connector to the device’s pole adapter. Note: While you could use the standard Hismith 3XLR to Kliclok adapter, there are two reasons why this is not a good idea. • It adds several inches of height to the pole on the device, which means that the captive may have to stand on tiptoe to mount the device. • It also adds a fair amount of wobble as there is now an additional connection joint. Figure 1–1 Completed pole adapter with Hismith Kliclok connector and metal dildo Hismith makes a very complete line of high-quality silicone and metal dildos ranging from average size and shape to some fantasy monster ones that very few people will be able to use. Their catalog page can be found here: https://www.hismith.com/en/71-attachments Here are some sample metal and silicone dildos I purchased for use with the device, with a tape measure (in inches) for scale: 1–1 Introduction Figure 1–2 Hismith polished metal dildos 1–2 Introduction Figure 1–3 Hismith silicone dildos (realistic and fantasy) Note: While each Hismith component has a part number, these numbers are not marked on the items themselves and sometimes not on the packaging. This can make it difficult to refer accurately to a specific part. 1–3 2 Necessary and optional parts To build the Kliclok adapter, you will need the following: • The "Ultimate Evil" One Bar Prison Construction and Usage manual V1.1b • This addendum • Hismith HSC03 Kliclok System Doubler [Amazon B07Z9V813H] qty. 1 • Hismith Kliclok dildos (as desired) • Hillman 270064 5/16" x 1-1/4" zinc finish flat washer [Lowe’s 68880] qty. 1 • Hillman 290006 3/16" x 1-1/4" zinc finish fender washer [Lowe’s 2576] qty. 2 • Hillman 880831 M6-1.00 x 25 socket head cap screw [2-pack Lowe’s 138531] qty. 1 • Ty-Rap TY525MX Cable Ties [100-pack Amazon B001DEHZ14] qty. 1 (for optional anti-escape) • Xcelite 170M Shear Cutter [Amazon B0002BBZIS] qty. 1 (for optional anti-escape) • General purpose box cutter qty. 1 (for optional anti-escape) 2–1 3 Assembling the Kliclok connector and pole adapter In this chapter, we will create the combined Kliclok connector and pole adapter that becomes the connecting point for the various dildos. Note: Hismith is the only source for Kliclok hardware, so the choice of connector attachment methods is limited. Rather than using the epoxy method as was done for the 3XLR version, a screw is used for this assembly. The HSC03 Doubler was chosen because the HSC13 quick air adapter shaft was too thin to make a good epoxy bond with the pole adapter. 3.1 Preparing the pole adapter Prepare the pole adapter as shown in the "Ultimate Evil" One Bar Prison Construction and Usage manual Section 11.1. 3.2 Disassembling the Kliclok System Doubler You should now remove one of the Kliclok sockets from the HSC03 doubler. Use the hex wrench provided with the doubler. Set aside the socket, wrench, and lock washer for later use. Put the remaining parts of the doubler and the leftover screw back in the doubler package for future use. For example, if the Kliclok connector becomes damaged, you can swap it with the other one from the HSC03 doubler. 3–1 Assembling the Kliclok connector and pole adapter Figure 3–1 Kliclok System Doubler and Wrench 3.3 Assembling the Kliclok connector to the pole adapter Place the 5/16" x 1-1/4" zinc washer over the bottom end of the Kliclok adapter. Using a 1/4" drill bit or a file, enlarge the center hole in each of the two 3/16" x 1-1/4" zinc fender washers. Caution: Make sure the drill bit or file does not bind in the washers when enlarging the hole. Place the lock washer left over from the HSC03 disassembly onto one of the M6-1.00 x 25 socket head cap screws, then put the two 3/16" x 1-1/4" zinc fender washers onto the socket head cap screw. Carefully insert the completed assembly into the pole adapter. The threaded end of the socket head cap screw should protrude through the top of the pole adapter. 3–2 Assembling the Kliclok connector and pole adapter Figure 3–2 Assembly of parts in pole adapter Thread the Kliclok connector and its 5/16" washer onto the exposed end of the socket head cap screw. Finger tighten, ensuring that the Kliclok connector and washer remain centered on the pole adapter as you tighten them. Use the hex key provided with the HSC03 doubler to continue to tighten the socket head cap screw securely. Note: This is the only thing preventing the captive from trying to unscrew the Kliclok connector from the pole adapter and escaping, so make sure it is sufficiently tight. 3–3 Assembling the Kliclok connector and pole adapter Figure 3–3 Completed assembly of Kliclok to pole adapter Now return to Chapter 12 in the "Ultimate Evil" One Bar Prison Construction and Usage manual V1.1b to continue with the pole modification and the pole adapter mounting. 3–4 4 Modifying the Kliclok connector to prevent escape As the Kliclok connector is a quick-disconnect type, if the captive is aware of this fact and can reach the connector, they can push down on the Kliclok ring and disconnect the dildo from the connector in order to escape. It was necessary to design a method of preventing this type of escape. Fortunately, a somewhat unexpected feature of the Kliclok system is that more of the coupling area is exposed when a dildo is latched into the connector. This is shown by the area above the red arrows in the following picture: Figure 4–1 Kliclok connector showing unmated and mated differences Using a Ty-Rap TY525MX cable tie, create a loose loop and slide it over the Kliclok connector to rest on the pole adapter, as shown below. Note: The TY525MX cable tie was specifically chosen for this application and other ties, even if sold as "compatible" or "identical", will likely not work. 4–1 Modifying the Kliclok connector to prevent escape Figure 4–2 Loose cable tie on the pole adapter Install your dildo of choice in the Kliclok connector until it latches. Once the dildo latches into the Kliclok connector, lift the cable tie and tighten it securely to prevent the Kliclok collar from being lowered by the captive. Use the Xcelite 170M cutter to cut the loose end of the cable tie flush with the body of the cable tie. WARNING: Ensure that the cable tie is cut off perfectly flush. Cuts on an angle or made with a dull cutter can leave sharp edges, which can cause personal injury. 4–2 Modifying the Kliclok connector to prevent escape Figure 4–3 Cable tie tightened and cut fl ush The cable tie preventing the Kliclok connector from being uncoupled, so the captive cannot escape via this method. This is similar to the modification of the 3XLR connector version, where the quick-disconnect button is modified to be flush with the surface of the connector. When you want to replace the dildo with another one, use the Xcelite 170M cutter or a box cutter to cut through the cable tie to remove it, as shown below. At this point, you can push down the collar of the Kliclok connector to release the dildo as usual. DANGER: Never attempt to cut the cable tie with a captive still on the device. Lower the pole using the control ring and ensure the captive is safely away from the device. Only then should you cut the cable tie. Failure to observe this precaution could injure the captive with the cable cutter. 4–3 Modifying the Kliclok connector to prevent escape Figure 4–4 Kliclok connector showing cut cable tie Repeat the procedure with another dildo if desired. § Sensuality is beautiful, and dominance and submission in the right context is a passionate art.—Sai Marie Johnson 4–4