Planning interior painting in Devonport ? Before adding a fresh coat to walls that have already been painted, take a closer look at the condition of the existing finish. Paint may appear fine from a distance, but peeling edges, grease, small cracks or a glossy surface can cause problems once the new coating is applied. A little preparation beforehand can help prevent patchy results, peeling and unnecessary repainting. You do not always need to remove every layer of old paint. In many cases, the existing coating can remain if it is firmly attached and properly prepared. The important part is knowing which areas need cleaning, repairing, sanding or priming before the new paint goes on. Table of Contents - Inspect the Existing Paint - Remove Dirt, Grease and Dust - Repair Holes and Cracks - Sand the Surface - Know When to Use Primer - Choose Paint That Suits the Surface - Preparation Mistakes to Avoid - When Professional Painting May Be Needed 1. Inspect the Existing Paint Walk around the room and check the walls in natural light. Look for paint that is lifting, bubbling, cracking or flaking. These areas should not be covered with another coat because the new paint may come away along with the old finish. Pay attention to corners, window frames, areas behind furniture and places where moisture may have affected the wall. If you notice bubbling paint near a bathroom, window or ceiling, find out whether condensation, water leaks or another moisture problem is responsible. A wall with firmly attached paint is usually easier to repaint than one with several damaged patches. Identifying these problems early helps you work out how much preparation the surface needs. 2. Remove Dirt, Grease and Dust Paint does not adhere well to surfaces covered in dust, grease or everyday grime. Walls near cooking areas can collect oily residue, while hallways and living spaces often have fingerprints, marks and dust along the edges. Start by removing cobwebs and loose dust with a soft brush or cloth. Clean marked areas using a suitable wall-cleaning product. If the walls are particularly dirty, clean the entire surface rather than just the visible spots. Follow the cleaner's instructions and rinse where necessary. Allow the walls to dry completely before continuing. Painting over damp surfaces can affect how the coating dries and may lead to adhesion problems. Clean skirting boards, door frames and other areas that will also receive paint. 3. Repair Holes, Cracks and Uneven Areas Old painted walls often have small dents, nail holes and marks left behind by furniture or previous repairs. These imperfections become more noticeable after repainting, especially when light falls across the wall. Fill small holes and shallow cracks with a suitable filler. Once the filler has dried, sand it until the repaired area is smooth and level with the surrounding surface. Remove the sanding dust before applying primer or paint. Larger cracks need more attention. If a crack keeps appearing after repairs, it may be related to movement rather than a simple surface defect. In that situation, it is worth investigating the cause before filling and repainting the area. 4. Sand the Surface Where Needed Sanding helps remove rough edges, smooth repaired areas and prepare glossy paint for another coating. You do not necessarily need to sand every wall back extensively, but shiny or uneven surfaces may need sanding to improve adhesion. If paint is peeling, scrape away the loose sections until the remaining coating is firmly attached. Sand the edges of the damaged area so the transition between old paint and exposed surface is less noticeable. Use appropriate protective equipment and manage sanding dust carefully. In older Australian homes, some paint may contain lead. If you suspect lead-based paint, avoid dry sanding, heat stripping or aggressive scraping. Get professional advice about safe handling before disturbing it. 5. Know When to Use Primer Primer is useful when the surface needs more than a standard topcoat. Bare plaster, exposed timber, repaired patches and certain stained areas often require a primer or sealer to help create a consistent base. If you are painting over a darker colour with a lighter one, a suitable primer may reduce the number of topcoats needed. It can also help prevent stains from showing through, provided the product is designed to block that type of stain. On walls with sound, clean paint, primer may not be necessary. Check the instructions for your chosen paint and primer rather than applying extra products without a reason. 6. Choose Paint That Suits the Surface The paint you choose should suit the room, surface and conditions. Bedrooms and living areas often work well with low-sheen finishes, while kitchens, bathrooms and busy hallways may benefit from a finish that is easier to clean. Exterior surfaces require a different approach. For exterior painting in Devonport, consider the exposure to moisture, wind, sunlight and salt air, particularly on coastal properties. Weatherboards, render, masonry and timber may require different preparation methods and paint products. Always check the manufacturer's instructions for surface compatibility, application temperatures and drying times before painting. 7. Preparation Mistakes Worth Avoiding - Applying fresh paint over peeling or loose coatings. - Leaving grease, dust or cleaning residue on walls. - Painting over damp areas without addressing the moisture source. - Skipping sanding on surfaces that need it. - Covering filler before it has completely dried. - Choosing paint without checking whether it suits the existing surface. These mistakes can affect the finish even when the paint itself is good quality. 8. When Professional Painting May Be Needed Some repainting jobs involve more than a quick clean and coat of paint. Extensive peeling, damaged plaster, stubborn stains, high areas or suspected lead-based coatings may require specialised preparation. Brush Bros Painting undertakes residential and commercial painting in Devonport , including repainting and surface preparation. When walls need repairs or the existing coating is in poor condition, having the surface assessed before painting can help avoid problems later. The condition of the old coating determines how much work is needed before repainting. Taking the time to clean, repair and prepare the surface properly makes the painting process easier and helps the new finish look more consistent.