NetApp Certified Storage Installation Engineer, ONTAP NS0-184 Free Questions https://www.passquestion.com/ NS0-184 .html Data ONTAP 9 supports which three features? (Choose three.) A. SMB 3.0 B. NFSv2 C. SnapMirror D. Infinite Volumes Answer: ACD Question 1 You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches. In this scenario. Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.) A. network port show -ipspace Cluster B. network interface show -vserver Cluster C. network device-discovery show -protocol cdp D. network interface show -vserver Cluster -fields auto-revert Answer: AB Question 2 Upon finishing the Installation of a new system for a customer, they request that you train them on how to administer the system. In this scenario, which two responses are appropriate? (Choose two.) A. Visit the NetApp MySupport Site and look for the Express Guides, they will guide you through the daily tasks and provide input and output examples. B. If you have a specific issue, you can visit the Knowledge Base Web site (https://kb.netapp,com). C. The answers to any of your questions can be found on the NetApp SmartSolve site (http://smartsolve.netapp.com). D. You should open a case with NetApp Support for all future questions with low priority and include the keyword "Training" in the title. Answer: AC Question 3 After you install an AFF A700 2-node cluster with DS224C shelves, Config Advisor reports that your SAS cabling is in mixed-path HA. You expected the SAS cabling be in quad-path HA. You physically verify the LED status on the controllers and the shelves and notice no irregularities. However, a reboot of the SAS expander does not change the output. In this scenario, what should you do next? A. Open a case with NetApp Support and turn off the disk shelves until the issue is solved. B. Disconnect the disk shelves from the controller and run Config Advisor again. C. Re-seat the SAS IO modules of the affected AFF A700 controller. D. Use multipath HA because it is the only cabling supported on an AFF A700 controller. Answer: C Question 4 Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01. In this scenario, which two statements are correct? (Choose two.) A. Configure an SNMP community string on the cluster. B. Configure DNS on the cluster. C. Configure a trap host on the cluster. D. Configure a firewall policy and allow SNMP. Answer: BC Question 5 You are asked to install six shelves to a production cluster. The cluster is running clustered Data ONTAP and is a 4-node cluster. All six shelves will be cabled to the same HA pair. The customer wants you to assign all the new disks to a single node in the cluster. Which three tools would help you accomplish this task? (Choose three.) A. the Hardware Universe Web-based tool B. the Synergy application C. the Config Advisor application D. the My AutoSupport Web-based tool E. the System Setup application Answer: ACD Question 6 You were dispatched to install a cluster made up of FAS8060 and FAS8080 controllers. There are three FAS8060 controllers and three FAS8080 controllers. Which solution would provide the largest possible cluster? A. a cluster made up of two nodes B. a cluster made up of four nodes C. a cluster made up of five nodes D. a cluster made up of six nodes Answer: B Question 7 What is the minimum number of disks required in a SAS shelf? A. half of the shelf's capacity B. one C. two D. there is no minimum Answer: D Question 8 A host cannot connect to the namespace configured on an NVMe-enabled SVM. In this scenario, what are two reasons for this problem? (Choose two.) A. The namespace has not been added to the subsystem B. The namespace has not be added to the igroup C. The igroup has an incorrect NQN. D. The subsystem has an incorrect NQN Answer: AD Question 9 After completing an installation, the customer wants to know how they can manually open a new technical case with NetApp Global Support. What are three ways to accomplish this task? (Choose three.) A. Use the support site. B. Use the NetApp Field Portal. C. Use the mobile app. D. Use a telephone. E. Use AutoSupport. Answer: CDE Question 10