GENUINE PARTS LEAF / ZE2 Part No. H4982 7TA0A Installation Manual Tonneau cover Nissan North America H4982 7TA0AIM_20250418 Page 1 of 9 A B E D C F Nissan North America H4982 7TA0AIM_20250418 Page 2 of 9 Not Applicable/No service Part# Tonneau cover does not provide load restraint. Do not place any object on top or hang object to Tonneau cover. If a problem occurs during installation, please contact Nissan dealer where product was purchased. When printing Templates, please select "Actual size" in setting. Con rm that Templates are printed to scale. C 2 Hook Pin Clean Cloth Water and soap solution Dealer Installation Recommended. CAUTION WARNING To clean tonneau cover use vaccum cleaner, soft brush or dry cloth. Do not use steamer or household cleanser. Flammable or dangerous materials should not be transported in your vehicle at any time. Tonneau cover is designed to cover normal cargo contents. Flammable or dangerous materials should not be transported in your vehicle at any time. PART NUMBER(S) REQUIRED FOR INSTALLATION: H4982 7TA0A B 2 Damper KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Tonneau Cover Scissors Masking Tape 5mm(13/64") Drill Bit Be careful not to scratch or damage any component during installation or removal. Punch 7mm(9/32") Drill Bit Drill Pliers Cutter INSTALLATION CAUTIONS: For proper installation please follow instructions carefully. Drill Template "A", "B-LH" and "B-RH" Note : Please con rm templates are to scale after printing installation manual. TOOLS REQUIRED: Flat File 999V2 NADS0 Accessory Installation Manual Download Instructions 1 F D 2 Hook Grommet E 2 Washer Nissan North America H4982 7TA0AIM_20250418 Page 3 of 9 Nissan North America H4982 7TA0AIM_20250418 Page 4 of 9 - 1.1 SECTION 1 Tonneau cover installation Fig.1 Print out Template "A", "B-LH" and "B-RH" (Total 3 pages) in this Installation manual with actual scale. And cut all templates for drilling. 1.2 Overlap Template "B-LH 2" on gray area of "B-LH 1", and align outline of each Template and marking lines as shown in Fig.2. Then tape together. Take same step for Template "B-RH 1" and "B-RH 2". Fig.2 Fig.3 Align black arrows on Template "A-LH" to Rear window defrosters(4th and 5th from top), and secure it with masking tape. Punch at center of marking(x1), and remove Template"A-LH". Then drill with 7mm(9/32") bit. Repeat RH side using Template "A-RH". 1.3 Template A 5th φ7mm (9/32'') Front of Vehicle 4th 3rd 2nd 1st Template B-LH Template B-RH B-LH 1 B-LH 2 B-RH 1 B-RH 2 A-LH A-RH Masking tape Masking tape Template A-LH Tape Template B-LH 1 Template B-LH 2 Align Marking line Template B-LH 1 Template B-LH 2 Nissan North America H4982 7TA0AIM_20250418 Page 5 of 9 - Fig.6 1.6 Punch at center of marking(x2 each slot), and remove Template "B-LH" and "B-RH". Drill with 5mm(13/64") bit and le black area to be 5mm x 12mm slot. SECTION 1 Tonneau cover installation Fig.5 1.5 Align Template "B-LH" and "B-RH" as shown in Fig.5. Secure Templates with masking tape. Fig.4 1.4 Subassemble Hook Pin(C), Hook Grommet(D) and Washer(E). Insert it to trim then push Hook pin(C). Repeat RH side. Masking tape cv cv cv φ5mm (13/64'') File 5mm 12mm φ5mm x 2 Align Align Subassembled hook Washer(E) Hook Grommet(D) Hook Pin(C) 2. Push 1. Insert Hook Pin(C) Front of Vehicle Gap Template B-LH Template B-RH No Gap Tape Tape Tape Tape Nissan North America H4982 7TA0AIM_20250418 Page 6 of 9 - SECTION 1 Tonneau cover installation Fig.9 1.9 Hang rope end on Hook Pin(C) both side. Fig.7 1.7 Spray Soap and water on Damper(B) and install it by applying presssure with slight rotation as shown in Fig.7. CAUTION Make sure Damper(B) is installed properly in correct orientation. Fig.8 1.8 Insert right side clip of Tonneau Cover(A) into protrusion of luggage side trim. Then push Tonneau Cover(A) down to engage clip to protrusion of luggage side trim left side. Hook Pin(C) Rope Insert Right side Left side Tonneau Cover(A) Tonneau cover(A) Clip Clip Protrusion Protrusion Clip Clip Push Insert part of Damper(B) Damper(B) 5mm x 12mm slot CAUTION ZE2/LEAF TONNEAU COVER TEMPLATE-A CUT AWAY TEMPLATE HERE CUT AWAY TEMPLATE HERE 100 50 150 100 50 PRINT TEMPLATE 1 : 1 SCALE mm H4982 7TA0AIM_20250418 Page 7 of 9 ALIGN WITH 4 TH DEFROSTER ALIGN WITH 5 TH DEFROSTER TAPE TAPE ALIGN WITH REAR GLASS Φ7mm ( 9/32”) Drill Template A-RH (For Back door pillar trim) ALIGN WITH REAR GLASS ALIGN WITH 4 TH DEFROSTER ALIGN WITH 5 TH DEFROSTER TAPE ALIGN WITH REAR GLASS Φ7mm ( 9/32” ) Drill Template A-LH (For Back door pillar trim) ALIGN WITH REAR GLASS TAPE CUT AWAY TEMPLATE HERE CUT AWAY TEMPLATE HERE ZE2/LEAF TONNEAU COVER TEMPLATE-B-RH 100 50 150 100 50 PRINT TEMPLATE 1 : 1 SCALE mm H4982 7TA0AIM_20250418 Page 8 of 9 Drill Template B-RH 1 (For Back door lower trim) ALIGN WITH TRIM TAPE TAPE TAPE Φ5mm×2 (13/64”) TAPE Drill Template B-RH 2 (For Back door lower trim) TAPE TAPE TAPE TAPE TAPE Overlap “Drill Template B-RH 2” here. CUT AWAY TEMPLATE HERE CUT AWAY TEMPLATE HERE ZE2/LEAF TONNEAU COVER TEMPLATE-B-LH 100 50 150 100 50 PRINT TEMPLATE 1 : 1 SCALE mm H4982 7TA0AIM_20250418 Page 9 of 9 Drill Template B-LH 1 (For Back door lower trim) ALIGN WITH TRIM TAPE TAPE Φ5mm×2 (13/64”) Drill Template B-LH 2 (For Back door lower trim) TAPE TAPE TAPE TAPE TAPE TAPE TAPE Overlap “Drill Template B-LH 2” here.